Skip to main content
(844) 422-7000
A restaurant owner in a white chef coat reads her phone at the open door of a stainless walk-in cooler in a Charleston brick kitchen, with one small white sensor stuck to the cooler's inside wall

Lowcountry asset monitoring

Protect inventory with a freezer temperature alarm

CloudCentric installs wireless sensors across Charleston and Savannah to send alerts when coolers warm up or pipes leak.

Wireless sensors for Lowcountry businesses

Small sensors fit into tight spaces without new wiring. Every reading reports to the same app used for building cameras and door access.

Cooling systems fail overnight when kitchen staff is away. Battery-powered sensors monitor walk-in coolers and freezers, sending alerts to staff when temperatures rise or water leaks.

Walk-in coolerOut of range
1Heat builds
2Rule applies
3Phone alerts
  • Walk-in coolerMounts with adhesive
  • FreezerRated to -4 F
  • Leak probeAttaches to sensor

Cooling limits during power outages

FDA guidelines state how long food stays cold during power outages. Sensors send alerts when temperatures leave safe ranges so staff can act.

0 °F freezer (-18 °C)40 °F or below refrigerator (4 °C)FDA guidance

Discard perishable food like meat or milk held above 40 F for 4 hours. FDA, power outages and floods

Remote temperature monitoring on one screen

Sensor Manager displays live data and historical trends. Users see temperature, humidity, and leak status for every sensor in the building.

The manufacturer's Sensor Manager device panel for a bathroom sensor, showing 10 degrees Celsius, 40 percent humidity, 10 lux and a Leaking flagThe manufacturer's Sensor Manager with a temperature graph over one day and a table listing each sensor's temperature, humidity, light, leak status and last motion, one row reading Leaks DetectedThe manufacturer's Sensor Manager settings panel listing the selected sensors, a battery estimate, and Temperature, Humidity and Light ranges with a Safe ZoneThe manufacturer's Temperature Safe Zone dialog with a slider for the safe range and Apply, Cancel and Delete Safe Zone buttons
Manufacturer demonstration data shows Celsius readings using all-in-one sensor models.

Custom alerts for every condition

Alarm Manager sends notifications using rules with a trigger, a scope, and an action. Triggers can follow specific schedules.

The manufacturer's Alarm Manager rule editor, with a trigger, the devices it covers and the action that notifies
Alarm Manager: a rule picks the trigger and who is told.
  • Trigger conditionsDefine alarms for water leaks, smoke, carbon monoxide, or extreme values.
  • Schedule and scopeApply alerts to specific sensors during business hours or overnight.
  • NotificationsSend push notices or emails to chosen staff members automatically.
  • Repeat suppressionActivate ignore repeated actions to stop constant alerts once notified.

Long-range wireless coverage

Sensors reach gateways up to 2 km away in line of sight. One gateway supports up to 96 sensors, and additional gateways expand coverage.

  • Two kilometer rangeSensors reach gateways up to 2 km away in line of sight.
  • High sensor capacityEach gateway connects up to 96 sensors across building spaces.
  • Optimal placementMounting high on a wall or DIN rail in a central location with few obstructions supports coverage.
The manufacturer's diagram of a gateway linked to a switch and a cloud gateway, with eight Environmental Sensors scattered around it on dotted SuperLink radio paths
Manufacturer's diagram: sensors link to the gateway by SuperLink radio.

Operating limits and requirements

01

Compliance and certifications

Sensors report readings but carry no food-safety or vaccine-storage certificates. CDC data logger programs require separate calibrated devices.

02

Range and obstructions

Two kilometer range applies to line of sight. Walls and metal surfaces shorten actual wireless distance.

03

Required hardware

System operation requires a gateway and a compatible console. Both must be installed for sensors to report.

04

Safety systems

Sensors do not replace code-required fire alarms. Hardware provides monitoring only and does not control heating or cooling.

Monitoring hardware

Battery-powered sensors report to a gateway mounted on a wall or DIN rail.

Environmental Sensor, face-on
Environmental Sensor$49.00 UniFi store price, checked 2026-11-08Environmental sensor tracks conditions
SuperLink Gateway, face-on
SuperLink Gateway$129.00 UniFi store price, checked 2026-11-08SuperLink gateway connects sensors
SuperLink Gateway HA with its antenna
SuperLink Gateway HAHA gateway adds LTE and Thread support
All-In-One Sensor
All-In-One SensorAll-in-one sensor monitors motion
Environmental Sensor dimensioned drawing: 49 millimeters tall, 53 millimeters wide, 23.5 millimeters deep, with its status light, signal light, light sensor, water sensors, function button and temperature and humidity sensor labeled
Environmental Sensor, 53 x 49 x 23.5 mm (about 2.1 x 1.9 x 0.9 in). Manufacturer's drawing.
An Environmental Sensor lifted off its mounting plate on a tiled wall, with the plate held by two screws
Adhesive, magnet or screw mount. Manufacturer's image.

Installation process

  1. 1

    Site walkthrough

    Review building layout and gateway locations.

  2. 2

    System configuration

    Set up console and link monitoring software.

  3. 3

    Hardware mounting

    Install sensors in coolers and closets.

  4. 4

    Alert testing

    Verify notifications arrive on staff phones.

A property manager in a navy polo checks his phone outside the open water heater closet of a raised Isle of Palms beach house, with a small white sensor and its cable on the floor beside the heater

Common questions

Sensors for coolers, closets, and leaks

Call (844) 422-7000 to discuss sensors for your business.

CharlestonMount PleasantNorth CharlestonSummervilleBeaufortBlufftonHilton HeadSavannah
Call (844) 422-7000
CloudCentric · Mount Pleasant, SC · serving Charleston and the Lowcountry(844) 422-7000